|
These “quick install” cost effective Centralized Lubrication Systems are pre-assembled with compatible components
to minimize specification, purchasing and installation time. The automatic lubrication systems operate on a 120V,
60Hz 1Ph electrical supply for the motor. The systems are sized to meet most lubrication requirements where a
compressed air supply is not available. Each pump outlet is independently and externally adjustable 0 to .012 cu in
(0 to .197 cu cm) by using a fine micrometer thread .025 (.572mm) pitch adjustment. Each pump outlet will actuate
once per minute of motor run time.
|
STANDARD MATERIALS:
- Aluminum, Brass, Steel, transparent polymer
- Buna N & Viton seals
- Painted Steel Nema Type 12 & 13 Box
- For additional component information see Bulletins F1837-2, F357-7, F1867-1 & F1867-2
|
OPERATING CONDITIONS:
- Maximum operating temperature up to 120°F (48.9°C)
Minimum operating temperature 0°F (-17.7°C) oil
Minimum operating temperature 32°F (0°C), grease
- Maximum output pressure up to 50 PSIG (345 kPa)
- 120V, 60Hz, 4 W
|
*Caution: When using grease both the
PMP100 Series and PMP200 Series
Precision Metering Pumps are capable of
dispensing nearly all types and grades of
grease used in most general industrial,
indoor or controlled temperature
applications of 32°F (0°C) or above. The
combination of higher viscosities, ambient
temperatures lower than 32°F (0°C),
excessively long runs of output feed lines,
along with the type and use of smaller
inside diameter feed lines, will have an
effect on the feed rate and output
capabilities of these pumps.
|
|
MODIFICATIONS AVAILABLE MADE TO ORDER - CONSULT OUR FACTORY
|
| FOR OIL APPLICATION |
|
CAT NO.
|
RES CAP
|
NO. OF
FEEDS
|
W x H
|
O.A.
DEPTH
|
|
PMP640-01
|
1 QT.
|
1
|
7.00"
x
16.00"
|
6.38"
|
|
PMP640-02
|
1 QT.
|
2
|
|
PMP640-03
|
1 QT.
|
3
|
|
PMP640-04
|
1 QT.
|
4
|
|
PMP660-01
|
.5 GAL
|
1
|
7.00"
x
18.12"
|
|
PMP660-02
|
.5 GAL
|
2
|
|
PMP660-03
|
.5 GAL
|
3
|
|
PMP660-04
|
.5 GAL
|
4
|
|
| *FOR GREASE APPLICATION |
|
CAT NO.
|
RES CAP
|
NO. OF
FEEDS
|
W x H
|
O.A.
DEPTH
|
|
PMP630-01
|
75 CU IN
|
1
|
7.00"
x
17.80"
|
6.56"
|
|
PMP630-02
|
75 CU IN
|
2
|
|
PMP630-03
|
75 CU IN
|
3
|
|
PMP630-04
|
75 CU IN
|
4
|
|
PMP650-01
|
168 CU IN
|
1
|
7.00"
x
22.55"
|
|
PMP650-02
|
168 CU IN
|
2
|
|
PMP650-03
|
168 CU IN
|
3
|
|
PMP650-04
|
168 CU IN
|
4
|
|
PRODUCTS | TYPICAL APPLICATIONS | NEWS | VESCOR | FLODAR | HYDRA-TOOL | CONTACT US | SITEMAP